Hydraulic rod seals type S8
The S8 type is a highly efficient one-way compression type seal for piston rods. It consists of a fabric-reinforced "U"-shaped ring in which a rubber energizer is embedded. At low pressure, the pre-compression of the sealing section provides a low-pressure preload to obtain an effective seal at high pressure. When the pressure increases, the rubber component exerts force on the "U"-shaped component to deform it, increasing the contact surface of the seal and thus improving the sealing effect. The fabric parts are used to protect the rubber parts due to their high strength and durability, and the fabric parts can maintain the oil film to provide low friction and reduce wear.
Applications:
Working pressure: ≤25MPa
Working temperature: -30℃～+100℃
Reciprocating speed: ≤0.5m/s
Extrusion gap: The large gap size that appears on the non-pressure side during seal operation is crucial for the sealing function. When the gap size is larger than the value given in the table below, a plastic retaining ring should be installed behind the seal.
Section size Maximum allowable gap size
16MPa 25MPa
≤6 0.2 0.1
>6-0 0.2 0.1
>10-15 0.2 0.1
Medium: General petroleum-based hydraulic oil, water, emulsified type.
Installation:
To avoid damage to the sealing lip, precautions should be taken to avoid sharp edges during installation.
Material:
Rubber sandwich fabric, NBR
Hydraulic rod seal TDI 40x48x8 PU93 + PTFE up to 400 bar KVK/China
Product data
Ød=40 mm ; ØD=48 mm ; h=8 mm ; b1=8.5 mm ; e=6 mm
Material: PU93 + PTFE
Application range (the following limit values cannot appear at the same time):
Pressure: ≤ 400 bar
Speed: ≤ 1 m/s
Temperature: -30°C ~ +100°C
Media: mineral-based hydraulic oils and emulsions; not suitable for environmetally-friendly oils (bio oils)
Manufacturer:
Zhongxingshun Sealing Products Factory
In stock 20 pcs.
Hydraulic rod seal TDI 36x44x8 NBR85 + PTFE up to 350 bar KVK/China
Product data
Ød=36 mm ; ØD=44 mm ; h=8 mm ; b1=8.5 mm ; e=6 mm
Material: NBR85 + PTFE
Application range (the following limit values cannot appear at the same time):
Pressure: ≤ 350 bar
Speed: ≤ 1 m/s
Temperature: -30°C ~ +100°C
Media: mineral-based hydraulic oils and emulsions; not suitable for environmetally-friendly oils (bio oils)
Manufacturer:
Zhongxingshun Sealing Products Factory
In stock 20 pcs.
Hydraulic rod seal S8 40x48x6 NBR90/fabric NBR 250 bar KVK/China
Product data
The type S8 is a highly efficient one-way compression seal for piston rods. It consists of a fabric-reinforced "U"-shaped ring in which a rubber energizing element is embedded.
Ød=40 mm ; ØD=48 mm ; h=6 mm ; HA=6.4 mm ; C=2.5 mm
Material: PU90
Application range (the following limit values cannot appear at the same time):
Pressure: ≤ 250 bar
Speed: ≤ 0.5 m/s
Temperature: -30°C ~ +100°C
Media: mineral-based hydraulic oils and emulsions; not suitable for environmetally-friendly oils (bio oils)
Manufacturer:
Zhongxingshun Sealing Products Factory
In stock 20 pcs.
Hydraulic rod seal S8 53x63x7.5 NBR90/fabric NBR 250 bar KVK/China
Product data
The type S8 is a highly efficient one-way compression seal for piston rods. It consists of a fabric-reinforced "U"-shaped ring in which a rubber energizing element is embedded.
Ød=53 mm ; ØD=63 mm ; h=7.5 mm ; HA=8 mm ; C=3 mm
Material: PU90
Application range (the following limit values cannot appear at the same time):
Pressure: ≤ 250 bar
Speed: ≤ 0.5 m/s
Temperature: -30°C ~ +100°C
Media: mineral-based hydraulic oils and emulsions; not suitable for environmetally-friendly oils (bio oils)
Manufacturer:
Zhongxingshun Sealing Products Factory
In stock 10 pcs.
